ISO/TS TECHNICAL SPECIFICATION 8062-2 First edition 2013-07-01 Geometrical product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 2: Rules Speécification géomeétrique des produits (GPS) - Tolerances dimensionnelles et geométriques des pieces moulées - Partie 2: Regles d'utilisation Reference number IS0/TS 8062-2:2013(E) ISO @ IS0 2013 ed without license from IHS Not for Resale IS0/TS 8062-2:2013(E) COPYRIGHTPROTECTEDDOCUMENT ISO2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISOcopyrightoffice Case postale 56:CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax +4122 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland @ IS0 2013 - All rights reserved No reproductic networking permited without license from IHS Not for Resale IS0/TS 8062-2:2013(E) Contents Page Foreword ..iv Introduction. ..V 1 Scope. .1 2 Normative references 3 Terms and definitions ..2 4 Symbols. ..3 5 Designation on drawings ..5 6 Drawing type indicator ..5 6.1 Single and combined drawings ..5 6.2 Final moulded part drawings .5 6.3 Intermediate machined moulded part drawings .6 6.4 Finalmachinedmouldedpartdrawings 6.5 Identifier for machining by the supplier. .6 7 Drawing indications .7 7.1 Surface texture symbols 7.2 Part condition identifiers .7 7.3 Required machining allowance, RMA 10 8 Indication of general tolerances ..11 8.1 General tolerances according to IS0 8062-3 .11 8.2 Generalsurfaceprofiletolerance .11 9 Types of specifications ..12 9.1 General ..12 9.2 Specification of final moulded-part condition ..12 9.3 Specification of intermediate machined moulded-part conditions ..13 9.4 Specification of final machined moulded-part condition ..14 10 Tolerancing ..14 10.1 ..14 General 10.2 Tolerancing of final moulded parts ..14 10.3 Tolerancing of intermediate machined moulded parts ..15 10.4 Tolerancing of final machined moulded part. ..15 Annex A (normative) Proportions and dimensions of graphical symbols .19 Annex B (informative) Accumulation method, relationship between moulded part and machined moulded part. .21 Annex C (informative) Calculation of moulded part nominal dimensions of features to be machined. ..26 Annex D (informative) Examples for the multiple tolerancing method ..28 Annex E (informative) Drawing examples ..41 Annex F (informative) Task assignment. ..51 Annex G (informative) Relation to the GPS matrix model ..54 Bibliography ..56 iii se with IS ed without license from IHS Not for Resale

.pdf文档 ISO TS 8062-2 2013 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2 Rules

文档预览
中文文档 65 页 50 下载 1000 浏览 0 评论 309 收藏 3.0分
温馨提示:本文档共65页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
ISO TS 8062-2 2013 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2  Rules 第 1 页 ISO TS 8062-2 2013 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2  Rules 第 2 页 ISO TS 8062-2 2013 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2  Rules 第 3 页
下载文档到电脑,方便使用
本文档由 人生无常 于 2024-08-26 09:37:51上传分享
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们微信(点击查看客服),我们将及时删除相关资源。