IEC International ISO Standard ISO/IEC22460-1 First edition Cards and security devices for 2025-05 personalidentificationIsoUAs licence and drone or UAS security module- Part 1: Physical characteristics and basic datasetsforUASlicence Cartes etdispositifsdesécuritepourI'identificationdes personnes-PermisIsOetmoduled'identitededronepour lesdrones (vehiculesultralegersousystemes d'aeronefs sans équipageabord)- Partie 1: Caracteristiques physiques et jeu de donnees de base pourles permisde systemes d'aeronefs sans équipagea bord Referencenumber ISO/IEC22460-1:2025(en) ?ISO/IEC2025 IS0/IEC22460-1:2025(en) COPYRIGHTPROTECTEDDOCUMENT IS0/IEC2025 be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,or posting on or Iso's member body in the country of the requester. ISO copyright office CP 401:Ch.de Blandonnet 8 CH-1214Vernier,Geneva Phone: +4122 749 0111 Email:[email protected] Website:www.iso.org Published in Switzerland @IS0/IEC2025-All rights reserved ii IS0/IEC22460-1:2025(en) Contents Page Foreword. .iv Introduction v 1 Scope .1 2 Normative reference(s) .1 3 Terms and definitions .1 4 Abbreviatedterms 5 5 DroneorUASremotepilotlicenceandremotecrewlicenceoverview 6 5.1 DroneorUASremotepilotlicenceandcrewlicence .6 5.2 Tiered licence system .7 5.3 DrL TG1 .7 5.4 DrL TG2 .7 5.5 UALTG3 .7 5.6 UALTG4 .8 5.7 UAL TG5 .8 5.8 UAL TG6. .8 5.9 Drone orUAS securitymodule .8 5.10 DroneorUASlicences .8 6 Human-readabledataelementsonIDrLorIUAL 10 6.1 General. .10 6.2 Visual presence .10 6.3 Dataelementtables .10 6.4 Basicdataelements .11 6.5 Card design 12 6.6 DroneorUAScategoriesandsymboldescriptions 12 6.7 Securityofan IDrLorIUAL 12 6.8 Proceduresforsecuringtheissuanceand useofIDrLs orIUALs 12 6.9 Card durability 12 6.10 Additionaldataelements .12 AnnexA(normative)Carddesign .14 AnnexB(normative)DroneorUAScategoriesandsymboldescriptions .22 AnnexC (informative)MainthreatstothesecurityofanIDrLorIUAL .24 AnnexD(informative)MappingbetweenISo,ICAOandEASAstandards .27 AnnexE(informative)DistinguishingthenumberofcountriesfordroneorUAsidentification .29 nationalcode Bibliography .35 @IS0/IEC 2025-All rights reserved ili IS0/IEC 22460-1:2025(en) Foreword Iso(theInternational OrganizationforStandardization)andIEC(theInternationalElectrotechnical Commission) form the specialized system forworldwide standardization.National bodiesthat are membersofISoorIECparticipateinthedevelopmentofInternationalStandardsthroughtechnical ISOandIECtechnicalcommittees collaborateinfields ofmutual interest.Other international organizations, governmental andnon-governmental, inliaison with IsOand IEC,alsotakepart in thework. The procedures used to develop this document and those intended for its further maintenance are described intheIso/EcDirectives, Part1.Inparticular,the differentapproval criterianeededforthedifferenttypes ofdocument should be noted.Thisdocument wasdrafted in accordancewiththeeditorial rules of theIso/ IEcDirectives,Part2(seewww.iso.org/directivesorwww.iec.ch/members_experts/refdocs). IsoandIECdrawattentiontothepossibilitythattheimplementationof thisdocumentmayinvolvethe useof (a)patent(s).Iso and IEctakenoposition concerning theevidence,validity or applicabilityof any claimedpatentrights in respectthereof.Asofthedateofpublication ofthisdocument, IsOandIEChad not received notice of (a)patent(s)which mayberequiredto implementthisdocument.However,implementers databaseavailableatwww.iso.org/patentsandhttps://patents.iec.ch.ISoandIEC shallnotbeheld responsibleforidentifying anyor all suchpatentrights. Anytradenameused in thisdocument isinformation givenforthe convenience of usersanddoesnot constitute an endorsement. relatedto conformityassessment,aswell asinformation about Iso's adherenceto theWorld Trade Organization (WTO)principles inthe Technical Barriersto Trade (TBT) see www.iso.org/iso/foreword.html. In the IEC,see www.iec.ch/understanding-standards. This document was prepared by Joint T